Hybrid Membranes of the Ureasil-Polyether Containing Glucose for Future Application in Bone Regeneration.

The application of mesenchymal stem cells (MSC) in bone tissue regeneration can have unpredictable results due to the low survival of cells in the process since the lack of oxygen and nutrients promotes metabolic stress. Therefore, in this work, polymeric membranes formed by organic-inorganic hybrid materials called ureasil-polyether for modified glucose release were developed in order to overcome the problems posed by a of lack of this nutrient. Thus, membranes formed by polymeric blend of polypropylene oxide (PPO4000) and polyethylene oxide (PEO500) with 6% glucose incorporation were developed. Physical-chemical characterization techniques were performed, as well as tests that evaluated thermal properties, bioactivity, swelling, and release in SBF solution. The results of the swelling test showed an increase in membrane mass correlated with an increase in the concentration of ureasil-PEO500 in the polymeric blends. The membranes showed adequate resistance when subjected to the application of a high compression force (15 N). X-ray diffraction (XRD) evidenced peaks corresponding to orthorhombic crystalline organization, but the absence of glucose-related peaks showed characteristics of the amorphous regions of hybrid materials, likely due to solubilization. Thermogravimetry (TG) and differential scanning calorimetry (DSC) analyses showed that the thermal events attributed to glucose and hybrid materials were similar to that seen in the literature, however when glucose was incorporated into the PEO500, an increase in rigidity occurs. In PPO400, and in the blends of both materials, there was a slight decrease in Tg values. The smaller contact angle for the ureasil-PEO500 membrane revealed the more hydrophilic character of the material compared to other membranes. The membranes showed bioactivity and hemocompatibility in vitro. The in vitro release test revealed that it is possible to control the release rate of glucose and the kinetic analysis revealed a release mechanism characteristic of anomalous transport kinetics. Thus, we can conclude that ureasil-polyether membranes have great potential to be used as a glucose release system, and their future application has the potential to optimize the bone regeneration process.

Dexamethasone Acetate Nanocrystals, Characterization and Dissolution Studies in Presence of Polymorphic Phases.

BACKGROUND: A drug with poor water-solubility, like Dexamethasone acetate, can present lower bioavailability conventional for pharmaceutical formulations, and the presence of polymorphs in the raw material can lead to drug quality problems. OBJECTIVE: In this study, nanocrystals of dexamethasone acetate were synthesized by high pressure homogenizer (HPH) method in surfactant poloxamer 188 (P188) solid dispersion and the bioavailable in raw material with polymorphism presence was evaluated. METHODS: The powder pre-suspension was prepared by the HPH process, and the nanoparticles formed were incorporated in P188 solutions. The nanocrystals formed were characterized by techniques of XRD, SEM, FTIR, thermal analysis by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), dynamic light scattering (DLS) to analyze the particle size and zeta potential, and in vitro evaluation by dissolution studies. RESULTS: The characterization techniques were adequate to show the presence of raw material with physical moisture between two dexamethasone acetate polymorphs. The nanocrystals formed in the presence of the P188 in the formulation showed a considerable increase in the rate of dissolution of the drug in the medium and in the size of the stable nanocrystals, even in the presence of dexamethasone acetate polymorphs. CONCLUSION: The results showed that it was possible to produce dexamethasone nanocrystals by HPH process with regular size by the presence of the small amount of P188 surfactant. This article presents a novelty in the development of dexamethasone nanoparticles that have different polymorphic forms in their physical composition.

Zinc-Based Nanoparticles Reduce Bacterial Biofilm Formation.

Biofilm formation is important for microbial survival in hostile environments and a phenotype that provides microorganisms with antimicrobial resistance. Zinc oxide (ZnO) and Zinc sulfide (ZnS) nanoparticles (NPs) present potential antimicrobial properties for biomedical and food industry applications. Here, we aimed to analyze, for the first time, the bactericidal and antibiofilm activity of ZnS NPs against Staphylococcus aureus, Klebsiella oxytoca, and Pseudomonas aeruginosa, all medically important bacteria in developed countries. We compared ZnS NPs antimicrobial activity to ZnO NPs, which have been extensively studied. Using the colorimetric XTT reduction assay to observe the metabolic activity of bacterial cells and the crystal violet assay to measure biofilm mass, we demonstrated that ZnS and ZnO had similar efficacy in killing planktonic bacterial cells and reducing biofilm formation, with S. aureus being more susceptible to both therapeutics than K. oxytoca and P. aeruginosa. Crystal violet staining and confocal microscopy validated that Zn NPs inhibit biofilm formation and cause architectural damage. Our findings provide proof of principle that ZnS NPs have antibiofilm activity, and can be potentially used in medical and food industry applications, such as treatment of wound infections or package coating for food preservation. IMPORTANCE Zinc (Zn)-based nanoparticles (NPs) can be potentially used in medical and food preservation applications. As proof of principle, we investigated the bactericidal and antibiofilm activity of zinc oxide (ZnO) and zinc sulfide (ZnS) NPs against medically important bacteria. Zn-based NPs were similarly effective in killing planktonic and biofilm-associated Staphylococcus aureus, Klebsiella oxytoca, and Pseudomonas aeruginosa cells. However, S. aureus was more susceptible to these investigational therapeutics. Although further studies are warranted, our findings suggest the possibility of future use of Zn-based NPs in the treatment of skin infections or preservation of food.

ZnO@ZIF-8 Nanoparticles as Nanocarrier of Ciprofloxacin for Antimicrobial Activity.

Numerous antimicrobial drugs have been prescribed to kill or inhibit the growth of microbes such as bacteria, fungi, and viruses. Despite the known therapeutic efficacy of these drugs, inefficient delivery could result in an inadequate therapeutic index and several side effects. In order to overcome this adversity, the present study investigated antibiotic drug loading in zeolitic imidazolate frameworks (ZIFs), in association with ZnO nanoparticles with known antimicrobial properties. In an economic synthesis method, the ZnO surface was first converted to ZIF-8 with 2-methylimidazole as a ligand, resulting in a ZnO@ZIF-8 structure. This system enables the high drug-loading efficiency (46%) of an antimicrobial drug, ciprofloxacin, within the pores of the ZIF-8. This association provides a control of the release of the active moieties, in simulated body-fluid conditions, with a maximum of 67% released in 96 h. The antibacterial activities of ZnO@ZIF-8 and CIP-ZnO@ZIF-8 were tested against the Gram-positive Staphylococcus aureus strain and the Gram-negative Pseudomonas aeruginosa strain, showing good growth inhibition. This result was obtained by combining ZnO@ZIF-8 with ciprofloxacin in a minimal inhibitory concentration (MIC) that was 10 times lower than ZnO@ZIF-8 for S. aureus and 200 times lower for P. aeruginosa, suggesting that CIP-ZnO@ZIF-8 may have potential application in prolonged antimicrobial treatment.

Piperine-loaded nanoparticles incorporated into hyaluronic acid/sodium alginate-based membranes for the treatment of inflammatory skin diseases.

Piperine is an alkaloid mostly found in the fruits of several species of the Piper genus, and its anti-inflammatory potential is already known. However, its therapeutic applications still need to be better explored due to the low aqueous solubility of this active. To overcome this drawback, the objective of this work was to evaluate the efficiency of the nanoencapsulation of the compound as well as its incorporation into hyaluronic acid/alginate-based biomembranes. Polymeric nanoparticles composed of Eudragit S100 and Poloxamer 188 were obtained by the nanoprecipitation technique, obtaining spherical nanosized particles with an average diameter of 122.1 ± 2.0 nm, polydispersity index of 0.266, and encapsulation efficiency of 76.2 %. Hyaluronic acid/sodium alginate membranes were then prepared and characterized. Regarding permeation, a slow passage rate was observed until the initial 14 h, when an exponential increase in the recovered drug concentration began to occur. The in vivo assay showed a reduction in inflammation up to 43.6 %, and no cytotoxicity was observed. The results suggested the potential of the system developed for the treatment of inflammatory skin diseases.

Sustainable Antibacterial Activity of Polyamide Fabrics Containing ZnO Nanoparticles.

In this study, we present an unprecedented study on the influence of parameters such as dyeing, softening, and number of washes on the maintenance of the antibacterial activity of polyamide fabrics containing zinc oxide nanoparticles (ZnO NPs) impregnated by a simple and easy-to-scale technique. ZnO NPs were synthesized by the sol-gel method at different reaction times (1, 3, and 24 h), followed by surface modification with (3-glycidyloxypropyl)trimethoxysilane (GPTMS) and water dispersion. The reaction times of ZnO NP synthesis were modified to evaluate their influence on particle size and antibacterial activity after impregnation in fabrics. The presence of ZnO NPs in fabrics was observed by different techniques such as X-ray diffraction, infrared vibrational spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The mean diameter values of the ZnO NPs calculated in this work from different techniques remained at 5 nm regardless of the reaction time revealing the efficient control of the nanoparticle size, important for desired applications as ZnO NPs smaller than 10 nm show improved antibacterial activity. The antibacterial activity of fabrics containing ZnO NPs indicated that polyamide fabrics after impregnation with ZnO NPs synthetized have great and similar biocidal potential against Staphylococcus aureus and Escherichia coli both with and without the presence of a fabric softener or a dye. The antibacterial behavior of the different polyamide fabrics remained after 10 and 20 washing cycles. The results shown in this study demonstrated the possibility of obtaining polyamide fabrics containing ZnO NPs with the antibacterial activity resistant to chemical treatments used by industries as a softener or a dye. The results also reveal the maintenance of the antimicrobial activity of fabrics after several washing cycles. The reaction time of 1 for the production of ZnO NPs and the versatility of polyamide fabrics allow their application in different environments to control microbial infections.

MIL-100(Fe) Sub-Micrometric Capsules as a Dual Drug Delivery System.

Nanoparticles of metal-organic frameworks (MOF NPs) are crystalline hybrid micro- or mesoporous nanomaterials that show great promise in biomedicine due to their significant drug loading ability and controlled release. Herein, we develop porous capsules from aggregate of nanoparticles of the iron carboxylate MIL-100(Fe) through a low-temperature spray-drying route. This enables the concomitant one-pot encapsulation of high loading of an antitumor drug, methotrexate, within the pores of the MOF NPs, and the collagenase enzyme (COL), inside the inter-particular mesoporous cavities, upon the formation of the capsule, enhancing tumor treatment. This association provides better control of the release of the active moieties, MTX and collagenase, in simulated body fluid conditions in comparison with the bare MOF NPs. In addition, the loaded MIL-100 capsules present, against the A-375 cancer cell line, selective toxicity nine times higher than for the normal HaCaT cells, suggesting that MTX@COL@MIL-100 capsules may have potential application in the selective treatment of cancer cells. We highlight that an appropriate level of collagenase activity remained after encapsulation using the spray dryer equipment. Therefore, this work describes a novel application of MOF-based capsules as a dual drug delivery system for cancer treatment.

Dexamethasone-Loaded Ureasil Hydrophobic Membrane for Bone Guided Regeneration.

Physical barrier membranes have been used to release active substances to treat critical bone defects; however, hydrophilic membranes do not present a prolonged release capacity. In this sense, hydrophobic membranes have been tested. Thus, this study aimed to develop hydrophobic membranes based on mixtures of ureasil-polyether-type materials containing incorporated dexamethasone (DMA) for the application in guided bone regeneration. The physicochemical characterization and biological assays were carried out using small-angle X-ray scattering (SAXS), an in vitro DMA release study, atomic force microscopy (AFM), a hemolysis test, and in vivo bone formation. The swelling degree, SAXS, and release results revealed that the u-PPO400/2000 membrane in the proportion of 70:30 showed swelling (4.69% ± 0.22) similar to the proportions 90:10 and 80:20, and lower than the proportion 60:40 (6.38% ± 0.49); however, an equal release percentage after 134 h was observed between the proportions 70:30 and 60:40. All u-PPO materials presented hemocompatibility (hemolysis ≤2.8%). AFM results showed that the treatments with or without DMA did not present significant differences, revealing a flat/smooth surface, with no pores and/or crystalline precipitates. Finally, in vivo results revealed that for both the commercial hydrophilic membrane and u-PPO400/2000 (70:30) after 60 days, the bone formation volume was 21%. In conclusion, hybrid membranes present unique characteristics for treating critical bone defects, considering the delayed and prolonged release results associated with the physical barrier capacity.

Magnetic and Highly Luminescent Heterostructures of Gd3+/ZnO Conjugated to GCIS/ZnS Quantum Dots for Multimodal Imaging.

In recent years, the use of quantum dots (Qdots) to obtain biological images has attracted attention due to their excellent luminescent properties and the possibility of their association with contrast agents for magnetic resonance imaging (MRI). In this study, Gd3+/ZnO (ZnOGd) were conjugated with Qdots composed of a gadolinium-copper-indium-sulphur core covered with a ZnS shell (GCIS/ZnS Qdots). This conjugation is an innovation that has not yet been described in the literature, and which aims to improve Qdot photoluminescent properties. Structural and morphological Qdots features were obtained by transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and thermogravimetric analyses (TGA). The photoluminescent properties were examined by emission (PL) and excitation (PLE) spectra. A new ZnOGd and GCIS/ZnS (ZnOGd-GCIS/ZnS) nanomaterial was synthesized with tunable optical properties depending on the ratio between the two native Qdots. A hydrophilic or lipophilic coating, using 3-glycidyloxypropyltrimethoxysilane (GPTMS) or hexadecyltrimethoxysilane (HTMS) on the surface of ZnOGd-GCIS/ZnS Qdots, was carried out before assessing their efficiency as magnetic resonance contrast agents. ZnOGd-GCIS/ZnS had excellent luminescence and MRI properties. The new Qdots developed ZnOGd-GCIS/ZnS, mostly constituted of ZnOGd (75%), which had less cytotoxicity when compared to ZnOGd, as well as greater cellular uptake.

Nanostructural Arrangements and Surface Morphology on Ureasil-Polyether Films Loaded with Dexamethasone Acetate.

Ureasil-Poly(ethylene oxide) (ureasil-PEO500) and ureasil-Poly(propylene oxide) (u-PPO400) films, unloaded and loaded with dexamethasone acetate (DMA), have been investigated by carrying out atomic force microscopy (AFM), ultrasonic force microscopy (UFM), contact-angle, and drug release experiments. In addition, X-ray diffraction, small angle X-ray scattering, and infrared spectroscopy have provided essential information to understand the films' structural organization. Our results reveal that while in u-PEO500 DMA occupies sites near the ether oxygen and remains absent from the film surface, in u-PPO400 new crystalline phases are formed when DMA is loaded, which show up as ~30-100 nm in diameter rounded clusters aligned along a well-defined direction, presumably related to the one defined by the characteristic polymer ropes distinguished on the surface of the unloaded u-POP film; occasionally, larger needle-shaped DMA crystals are also observed. UFM reveals that in the unloaded u-PPO matrix the polymer ropes are made up of strands, which in turn consist of aligned ~180 nm in diameter stiffer rounded clusters possibly formed by siloxane-node aggregates; the new crystalline phases may grow in-between the strands when the drug is loaded. The results illustrate the potential of AFM-based procedures, in combination with additional physico-chemical techniques, to picture the nanostructural arrangements in polymer matrices intended for drug delivery.

In vivo effectiveness of hybrid membranes with osteogenic growth peptide for bone regeneration.

Guided bone regeneration (GBR) technique helps to restore bone tissue through cellular selectivity principle. Currently no osteoinductive membrane exists on the market. Osteogenic growth peptide (OGP) acts as a hematopoietic stimulator. This association could improve the quality of bone formation, benefiting more than 2.2 million patients annually. The objective of this work was to develop membranes from ureasil-polyether materials containing OGP. The membranes were characterized by differential scanning calorimetry (DSC) and small angle X-ray scattering (SAXS). OGP was synthesized by the solid phase method. Sterilization results using gamma radiation at 24 kGy did not change the structure of the material, as confirmed by DSC. The SAXS technique revealed the structural homogeneity of the matrix. OGP was incorporated in 66.25 × 10-10  mol and release results showed that the ureasil-PPO400/PEO500 and ureasil-PPO400/PEO1900 membranes released 7% and 21%, respectively, after 48 h. In vivo results demonstrated that the amount and quality of bone tissue formed in the bone defects in the presence of ureasil-polyether membranes with OGP were similar to commercial collagen material with BMP. The results allow us to conclude that membranes with OGP have characteristics that make them potential candidates for the GBR.

Synthesis of ureasil-polyether film forming materials by using environmentally friendly solvent

Organic inorganic hybrids present several advantages as drug release systems, such as: high flexibility, high mechanical and thermal resistance, transparency, and low water solubility. These hybrids are synthesized through a chemical route named sol-gel that usually uses as solvente tetrahydrofuran (THF). Objetives: To develop film formers from hybrid materials replacing THF with ethanol, a less toxic solvent for skin application and for the environment. Methods: Four polymers were used: two based on polyethylene oxide (PEO) with molecular weight of 500 and 1900 g mol-1 and two based on polypropylene oxide (PPO), with molecular weight of 400 and 2000 g mol-1. The structural analysis was performed by FTIR, 1H-NMR and 29Si-NMR, and the thermal-mechanical analysis by DSC and TG-DTA. Results: The results of the thermo-mechanical analysis revealed that the solvent replacement did not affect the thermal stability and flexibility of the di-ureasil hybrid. Conclusions: Structural characterization confirmed the formation of hybrids both in THF and in ethanol. Therefore, ethanol is an excellent solvent for the synthesis of these hybrid matrices, since it allows obtaining the same material without changing its characteristics, with some advantages, however, over THF. Furthermore, this paper describes the efficiency of ethanol as a solvent, which is environmentally friendly, to replace THF in the physical-chemical characteristics of these filming former materials.

Relationship Between Structure And Antimicrobial Activity Of Zinc Oxide Nanoparticles: An Overview.

The inappropriate use of antimicrobials has resulted in the selection of resistant strains. Thus, a great number of studies have focused on the investigation of new antimicrobial agents. The use of zinc oxide nanoparticles (ZnO NPs) to optimise the fight against microbial resistance has been receiving increased attention due to the non-specific activity of inorganic antimicrobial agents. The small particle size and the high surface area of ZnO NPs can enhance antimicrobial activity, causing an improvement in surface reactivity. In addition, surface modifiers covering ZnO NPs can play a role in mediating antimicrobial activity since the surface properties of nanomaterials alter their interactions with cells; this may interfere with the antimicrobial effect of ZnO NPs. The possibility of using surface modifiers with groups toxic to microorganisms can improve the antimicrobial activity of ZnO NPs. Understanding the exact toxicity mechanisms is crucial to elucidating the antimicrobial activity of ZnO NPs in bacteria and fungi. Therefore, this review aims to describe the mechanisms of ZnO NPs toxicity against fungi and bacteria and how the different structural and physical-chemical characteristics of ZnO NPs can interfere in their antimicrobial activity.

Increased antibacterial activity of ZnO nanoparticles: Influence of size and surface modification.

In the current study, the size and surface of ZnO nanoparticle (ZnO NP) suspensions and powders were finely controlled to evaluate their influence on the ZnO antibacterial activity against Staphylococcus aureus and Escherichia coli. The ZnO NP were prepared by the sol-gel method with different reaction times for NP size control and followed by the addition of (3-glycidyloxypropyl) trimethoxysilane (GPTMS) as a surface modifier. The ZnO NP were characterized by different techniques and the antibacterial activity was assessed through the minimum inhibitory concentration assay (MIC), minimum bactericidal concentration assay (MBC) and scanning electron microscopy (SEM). The ZnO NP exhibited significant antibacterial activity against Staphylococcus aureus. The NP size highly influenced the antibacterial activity, which increased with decreasing particle size. The small ZnO NP presented bactericidal activity whereas the largest showed bacteriostatic activity. The use of GPTMS, in general, led to increase of MIC and MBC. The formation of holes in the cell wall of Staphylococcus aureus was evidenced by SEM after contact between the bacteria and ZnO NP. The cytotoxicity assay showed that ZnO NP did not cause a loss of cell viability in the human keratinocyte cell line (HaCat) at the maximum concentration assessed. Thus, this study indicated that 5 nm ZnO NP modified by GPTMS has great potential for use as an inorganic antibacterial material.

Assessment of an anti-ageing structured cosmetic formulation containing goji berry

Based on previous studies, it has been found that goji berry (GB), popularly known as a 'miracle fruit', has excellent antioxidant potential and can be used in the treatment of skin disorders associated with ageing. This study aimed to incorporate GB into a structured cosmetic in order to optimise its penetration. Stability studies of the formulation, determination of the antioxidant activity of the extract and of the formulation, rheological measurements, SAXS, polarised light microscopy and bioadhesion analyses were performed. The results indicated the antioxidant activity of the extract, which can be incorporated into an emulsified cosmetic formulation. The emulsified formulation containing the extract remained stable, even after being submitted to thermal and luminous stresses for 30 days. In addition, rheological tests revealed that the addition of the GB soft extract reduced the viscosity of the formulation, increasing thixotropy and deformation. These systems were characterised by SAXS as a lamellar phase, which was confirmed by polarised light microscopy. These highly organised structures indicate their excellent stability. In vitro bioadhesion experiments revealed that these formulations exhibited skin adhesion strength statistically similar to commercial anti-ageing formulation. These results suggest that this formulation has excellent potential to be used as a topical treatment for ageing.

The Critical Role of Thioacetamide Concentration in the Formation of ZnO/ZnS Heterostructures by Sol-Gel Process.

ZnO/ZnS heterostructures have emerged as an attractive approach for tailoring the properties of particles comprising these semiconductors. They can be synthesized using low temperature sol-gel routes. The present work yields insight into the mechanisms involved in the formation of ZnO/ZnS nanostructures. ZnO colloidal suspensions, prepared by hydrolysis and condensation of a Zn acetate precursor solution, were allowed to react with an ethanolic thioacetamide solution (TAA) as sulfur source. The reactions were monitored in situ by Small Angle X-ray Scattering (SAXS) and UV-vis spectroscopy, and the final colloidal suspensions were characterized by High Resolution Transmission Electron Microscopy (HRTEM). The powders extracted at the end of the reactions were analyzed by X-ray Absorption spectroscopy (XAS) and X-ray diffraction (XRD). Depending on TAA concentration, different nanostructures were revealed. ZnO and ZnS phases were mainly obtained at low and high TAA concentrations, respectively. At intermediate TAA concentrations, we evidenced the formation of ZnO/ZnS heterostructures. ZnS formation could take place via direct crystal growth involving Zn ions remaining in solution and S ions provided by TAA and/or chemical conversion of ZnO to ZnS. The combination of all the characterization techniques was crucial to elucidate the reaction steps and the nature of the final products.

Physicochemical characterization of drug nanocarriers.

Pharmaceutical design has enabled important advances in the prevention, treatment, and diagnosis of diseases. The use of nanotechnology to optimize the delivery of drugs and diagnostic molecules is increasingly receiving attention due to the enhanced efficiency provided by these systems. Understanding the structures of nanocarriers is crucial in elucidating their physical and chemical properties, which greatly influence their behavior in the body at both the molecular and systemic levels. This review was conducted to describe the principles and characteristics of techniques commonly used to elucidate the structures of nanocarriers, with consideration of their size, morphology, surface charge, porosity, crystalline arrangement, and phase. These techniques include X-ray diffraction, small-angle X-ray scattering, dynamic light scattering, zeta potential, polarized light microscopy, transmission electron microscopy, scanning electron microcopy, and porosimetry. Moreover, we describe some of the commonly used nanocarriers (liquid crystals, metal-organic frameworks, silica nanospheres, liposomes, solid lipid nanoparticles, and micelles) and the main aspects of their structures.

Guava: phytochemical composition of a potential source of antioxidants for cosmetic and/or dermatological applications

ABSTRACT Guava (Psidium guajava L.) is a native fruit of the American tropics with commercial applications for its taste, flavor and aroma. Numerous pharmacological uses have been described for it, such as the antiseptic effect of its leaves, the use of the fresh fruit and tea from its leaves for the treatment of diarrhea, dysentery, diabetes mellitus, and others. However, considering its rich composition, the guava also is a potential source of antioxidants to be used in the development of new formulations for cosmetic and/or dermatological applications, the main focus of this research. Herein, we describe the study of the phytochemical composition and the antioxidant activity of a guava extract prepared with non-toxic solvents aiming its use at biological applications. High performance liquid chromatography and mass spectrometry were employed to identify the major components, while thermoanalytical measurements and hot stage microscopy were used to assess the chemical stability of guava fruit extract. The antioxidant activity was also evaluated assessing the SOD-like activity and ABTS free radical scavenger. The results show that the extract is a rich source of phenolic compounds, such as quercetin, kaempferol, schottenol, among many others. All of the components found in guava extract exhibit biological effects according to the literature data, mainly antioxidant properties.

Design and Characterization of a Novel p1025 Peptide-Loaded Liquid Crystalline System for the Treatment of Dental Caries.

Dental caries, mainly caused by the adhesion of Streptococcus mutans to pellicle-coated tooth surfaces, is an important public health problem worldwide. A synthetic peptide (p1025) corresponding to residues 1025-1044 of the adhesin can inhibit this binding. Peptides are particularly susceptible to the biological environment; therefore, a p1025 peptide-loaded liquid crystalline system (LCS) consisting of tea tree oil as the oil phase, polyoxypropylene-(5)-polyoxyethylene-(20)-cetyl alcohol as the surfactant, and water or 0.5% polycarbophil polymer dispersions as the aqueous phase was employed as a drug delivery platform. This system exhibited anticaries and bioadhesive properties and provided a protective environment to p1025 at the site of action, thereby modulating its action, prolonging its contact with the teeth, and decreasing the frequency of administration. LCSs were characterized by polarized light microscopy (PLM), small-angle X-ray scattering (SAXS), and rheological, texture, and bioadhesive tests. PLM and SAXS revealed the presence of hexagonal liquid crystalline phases and microemulsions. Rheological analyses demonstrated that the addition of polymer dispersions favored characteristics such as shear thinning and thixotropy, hence improving buccal application. Bioadhesion tests showed that polymer dispersions contributed to the adhesion onto the teeth. Taken together, LCS could provide a novel pharmaceutical nanotechnology platform for dental caries treatment.

Design and Characterization of Silicone and Surfactant Based Systems for Topical Drug Delivery.

Nanotechnology offers advantages for new drug delivery design by providing drug targeting while minimizing the side effects. Polyoxyethylene 20 cetyl alcohol (CETETH-20) is a surfactant that may form nanostructured systems, such as liquid crystals, when in contact with water/oil, which are structurally similar to biological membranes and may improve skin interaction. The aim of this study was to develop and characterize CETETH 20-based nanostructured systems by combining CETETH-20 with water and different oily phases, including PEG-12-dimethicone for topical drug administration. The systems were characterized by polarized light microscopy (PLM), small-angle X-ray scattering (SAXS), rheology, texture profile analyses (TPA), in vitro cytotoxicity and histopathological analyses of rabbits' skin. Lamellar, hexagonal and cubic phases were identified and their viscoelastic moduli varied according to each phase. The stiffness of the cubic phase was 3-fold higher and twice more adhesive than the hexagonal phase. The formulations did not affect the normal macrophages cells, neither promoted skin irritation. They were spontaneously obtained by simply mixing the components, which corroborates for an ease scaled-up. These results suggest that systems composed of CETETH 20, PEG-12-dimethicone and water are a promising new approach for designing nanostructured topical drug delivery systems.